Network Configuration Reference¶

Network configuration is critical for building a high performance Ceph Storage Cluster. The Ceph Storage Cluster does not perform request routing or dispatching on behalf of the Ceph Client. Instead, Ceph Clients make requests directly to Ceph OSD Daemons. Ceph OSD Daemons perform data replication on behalf of Ceph Clients, which means replication and other factors impose additional loads on Ceph Storage Cluster networks.

Our Quick Start configurations provide a trivial Ceph configuration file that sets monitor IP addresses and daemon host names only. Unless you specify a cluster network, Ceph assumes a single “public” network. Ceph functions just fine with a public network only, but you may see significant performance improvement with a second “cluster” network in a large cluster.

We recommend running a Ceph Storage Cluster with two networks: a public (front-side) network and a cluster (back-side) network. To support two networks, each Ceph Node will need to have more than one NIC. See Hardware Recommendations - Networks for additional details.

There are several reasons to consider operating two separate networks:

Performance: Ceph OSD Daemons handle data replication for the Ceph Clients. When Ceph OSD Daemons replicate data more than once, the network load between Ceph OSD Daemons easily dwarfs the network load between Ceph Clients and the Ceph Storage Cluster. This can introduce latency and create a performance problem. Recovery and rebalancing can also introduce significant latency on the public network. See Scalability and High Availability for additional details on how Ceph replicates data. See Monitor / OSD Interaction for details on heartbeat traffic.
Security: While most people are generally civil, a very tiny segment of the population likes to engage in what’s known as a Denial of Service (DoS) attack. When traffic between Ceph OSD Daemons gets disrupted, placement groups may no longer reflect an active + clean state, which may prevent users from reading and writing data. A great way to defeat this type of attack is to maintain a completely separate cluster network that doesn’t connect directly to the internet. Also, consider using Message Signatures to defeat spoofing attacks.

IP Tables¶

By default, daemons bind to ports within the 6800:7300 range. You may configure this range at your discretion. Before configuring your IP tables, check the default iptables configuration.

sudo iptables -L

Some Linux distributions include rules that reject all inbound requests except SSH from all network interfaces. For example:

REJECT all -- anywhere anywhere reject-with icmp-host-prohibited

You will need to delete these rules on both your public and cluster networks initially, and replace them with appropriate rules when you are ready to harden the ports on your Ceph Nodes.

Monitor IP Tables¶

Ceph Monitors listen on port 6789 by default. Additionally, Ceph Monitors always operate on the public network. When you add the rule using the example below, make sure you replace {iface} with the public network interface (e.g., eth0, eth1, etc.), {ip-address} with the IP address of the public network and {netmask} with the netmask for the public network.

sudo iptables -A INPUT -i {iface} -p tcp -s {ip-address}/{netmask} --dport 6789 -j ACCEPT

MDS IP Tables¶

A Ceph Metadata Server listens on the first available port on the public network beginning at port 6800. Note that this behavior is not deterministic, so if you are running more than one OSD or MDS on the same host, or if you restart the daemons within a short window of time, the daemons will bind to higher ports. You should open the entire 6800-7300 range by default. When you add the rule using the example below, make sure you replace {iface} with the public network interface (e.g., eth0, eth1, etc.), {ip-address} with the IP address of the public network and {netmask} with the netmask of the public network.

For example:

sudo iptables -A INPUT -i {iface} -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7300 -j ACCEPT

OSD IP Tables¶

By default, Ceph OSD Daemons bind to the first available ports on a Ceph Node beginning at port 6800. Note that this behavior is not deterministic, so if you are running more than one OSD or MDS on the same host, or if you restart the daemons within a short window of time, the daemons will bind to higher ports. Each Ceph OSD Daemon on a Ceph Node may use up to four ports:

One for talking to clients and monitors.
One for sending data to other OSDs.
Two for heartbeating on each interface.

When a daemon fails and restarts without letting go of the port, the restarted daemon will bind to a new port. You should open the entire 6800-7300 port range to handle this possibility.

If you set up separate public and cluster networks, you must add rules for both the public network and the cluster network, because clients will connect using the public network and other Ceph OSD Daemons will connect using the cluster network. When you add the rule using the example below, make sure you replace {iface} with the network interface (e.g., eth0, eth1, etc.), {ip-address} with the IP address and {netmask} with the netmask of the public or cluster network. For example:

sudo iptables -A INPUT -i {iface}  -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7300 -j ACCEPT

Tip

If you run Ceph Metadata Servers on the same Ceph Node as the Ceph OSD Daemons, you can consolidate the public network configuration step.

Ceph Networks¶

To configure Ceph networks, you must add a network configuration to the [global] section of the configuration file. Our 5-minute Quick Start provides a trivial Ceph configuration file that assumes one public network with client and server on the same network and subnet. Ceph functions just fine with a public network only. However, Ceph allows you to establish much more specific criteria, including multiple IP network and subnet masks for your public network. You can also establish a separate cluster network to handle OSD heartbeat, object replication and recovery traffic. Don’t confuse the IP addresses you set in your configuration with the public-facing IP addresses network clients may use to access your service. Typical internal IP networks are often 192.168.0.0 or 10.0.0.0.

Tip

If you specify more than one IP address and subnet mask for either the public or the cluster network, the subnets within the network must be capable of routing to each other. Additionally, make sure you include each IP address/subnet in your IP tables and open ports for them as necessary.

Note

Ceph uses CIDR notation for subnets (e.g., 10.0.0.0/24).

When you have configured your networks, you may restart your cluster or restart each daemon. Ceph daemons bind dynamically, so you do not have to restart the entire cluster at once if you change your network configuration.

Public Network¶

To configure a public network, add the following option to the [global] section of your Ceph configuration file.

[global]
        ...
        public network = {public-network/netmask}

Cluster Network¶

If you declare a cluster network, OSDs will route heartbeat, object replication and recovery traffic over the cluster network. This may improve performance compared to using a single network. To configure a cluster network, add the following option to the [global] section of your Ceph configuration file.

[global]
        ...
        cluster network = {cluster-network/netmask}

We prefer that the cluster network is NOT reachable from the public network or the Internet for added security.

Ceph Daemons¶

Ceph has one network configuration requirement that applies to all daemons: the Ceph configuration file MUST specify the host for each daemon. Ceph also requires that a Ceph configuration file specify the monitor IP address and its port.

Important

Some deployment tools (e.g., ceph-deploy, Chef) may create a configuration file for you. DO NOT set these values if the deployment tool does it for you.

Tip

The host setting is the short name of the host (i.e., not an fqdn). It is NOT an IP address either. Enter hostname -s on the command line to retrieve the name of the host.

[mon.a]

        host = {hostname}
        mon addr = {ip-address}:6789

[osd.0]
        host = {hostname}

You do not have to set the host IP address for a daemon. If you have a static IP configuration and both public and cluster networks running, the Ceph configuration file may specify the IP address of the host for each daemon. To set a static IP address for a daemon, the following option(s) should appear in the daemon instance sections of your ceph.conf file.

[osd.0]
        public addr = {host-public-ip-address}
        cluster addr = {host-cluster-ip-address}

Network Config Settings¶

Network configuration settings are not required. Ceph assumes a public network with all hosts operating on it unless you specifically configure a cluster network.

Public Network¶

The public network configuration allows you specifically define IP addresses and subnets for the public network. You may specifically assign static IP addresses or override public network settings using the public addr setting for a specific daemon.

public network

Description:: The IP address and netmask of the public (front-side) network (e.g., 192.168.0.0/24). Set in [global]. You may specify comma-delimited subnets.
Type:: {ip-address}/{netmask} [, {ip-address}/{netmask}]
Required:: No
Default:: N/A

public addr

Description:: The IP address for the public (front-side) network. Set for each daemon.
Type:: IP Address
Required:: No
Default:: N/A

Cluster Network¶

The cluster network configuration allows you to declare a cluster network, and specifically define IP addresses and subnets for the cluster network. You may specifically assign static IP addresses or override cluster network settings using the cluster addr setting for specific OSD daemons.

cluster network

Description:: The IP address and netmask of the cluster (back-side) network (e.g., 10.0.0.0/24). Set in [global]. You may specify comma-delimited subnets.
Type:: {ip-address}/{netmask} [, {ip-address}/{netmask}]
Required:: No
Default:: N/A

cluster addr

Description:: The IP address for the cluster (back-side) network. Set for each daemon.
Type:: Address
Required:: No
Default:: N/A

Bind¶

Bind settings set the default port ranges Ceph OSD and MDS daemons use. The default range is 6800:7300. Ensure that your IP Tables configuration allows you to use the configured port range.

You may also enable Ceph daemons to bind to IPv6 addresses instead of IPv4 addresses.

ms bind port min

Description:: The minimum port number to which an OSD or MDS daemon will bind.
Type:: 32-bit Integer
Default:: 6800
Required:: No

ms bind port max

Description:: The maximum port number to which an OSD or MDS daemon will bind.
Type:: 32-bit Integer
Default:: 7300
Required:: No.

ms bind ipv6

Description:: Enables Ceph daemons to bind to IPv6 addresses. Currently the messenger either uses IPv4 or IPv6, but it cannot do both.
Type:: Boolean
Default:: false
Required:: No

public bind addr

Description:: In some dynamic deployments the Ceph MON daemon might bind to an IP address locally that is different from the public addr advertised to other peers in the network. The environment must ensure that routing rules are set correclty. If public bind addr is set the Ceph MON daemon will bind to it locally and use public addr in the monmaps to advertise its address to peers. This behavior is limited to the MON daemon.
Type:: IP Address
Required:: No
Default:: N/A

Hosts¶

Ceph expects at least one monitor declared in the Ceph configuration file, with a mon addr setting under each declared monitor. Ceph expects a host setting under each declared monitor, metadata server and OSD in the Ceph configuration file. Optionally, a monitor can be assigned with a priority, and the clients will always connect to the monitor with lower value of priority if specified.

mon addr

Description:: A list of {hostname}:{port} entries that clients can use to connect to a Ceph monitor. If not set, Ceph searches [mon.*] sections.
Type:: String
Required:: No
Default:: N/A

mon priority

Description:: The priority of the declared monitor, the lower value the more prefered when a client selects a monitor when trying to connect to the cluster.
Type:: Unsigned 16-bit Integer
Required:: No
Default:: 0

host

Description:: The hostname. Use this setting for specific daemon instances (e.g., [osd.0]).
Type:: String
Required:: Yes, for daemon instances.
Default:: localhost

Tip

Do not use localhost. To get your host name, execute hostname -s on your command line and use the name of your host (to the first period, not the fully-qualified domain name).

Important

You should not specify any value for host when using a third party deployment system that retrieves the host name for you.

TCP¶

Ceph disables TCP buffering by default.

ms tcp nodelay

Description:: Ceph enables ms tcp nodelay so that each request is sent immediately (no buffering). Disabling Nagle’s algorithm increases network traffic, which can introduce latency. If you experience large numbers of small packets, you may try disabling ms tcp nodelay.
Type:: Boolean
Required:: No
Default:: true

ms tcp rcvbuf

Description:: The size of the socket buffer on the receiving end of a network connection. Disable by default.
Type:: 32-bit Integer
Required:: No
Default:: 0

ms tcp read timeout

Description:: If a client or daemon makes a request to another Ceph daemon and does not drop an unused connection, the ms tcp read timeout defines the connection as idle after the specified number of seconds.
Type:: Unsigned 64-bit Integer
Required:: No
Default:: 900 15 minutes.